Question 1

After having configured the edge switch uplink as requested your colleague says that they have failed to ping the core You ask your colleague to verify the connection is plugged in and the switch is powered on They confirm that both are correct You attempt to ping the core switch and confirm that the ping is failing. Knowing the nature of this deployment, what commands might you use to troubleshoot this issued

Options :

A : Ping 10.11 1 - ping the core to attempt to verify connectivity Show trunk - to verify if the LAG interface was correctly added to the switch Show spanning tree - to check for spanning-tree blocked states Show port-access clients interface all - to view any port-access blocking states or failed authentication attempts on all interfaces Show run interface vlan20 - to double check the layer 3 svi configuration is correct for l_3 connectivity Show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports

B : diagnostic diag cable-diag 1/1/51 diag cable-diag 1/1/52 - to view diagnostic information for the physical link to get a status on any interruptions to Layer 1 connectivity, show ip route - to verify that the default gateway is present in the routing table show ip ospf - to check whether there is a layer 3 routing protocol enabled show ip dns - to view whether there is a valid dns source

C : Ping 10.1.1.1 - ping the core to attempt to verify connectivity show lacp agg - to verify which link aggregations are currently configured using which physical ports show lacp int - to verify the LACP status and whether any links are blocking in your topology show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 - to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 - to ensure you have the L3 SVI no shut and configured in the correct subnet

D : Show run - to view the running configuration of the switch Show run | begin 20 "vlan 20" - to ensure VLAN 20 was correctly added to the database show run | begin 20 'interface vlan 20' - to view the L3 SVI configuration Show run interface 1/1/51.1/1/52 - to ensure the physical interfaces are no shut and were added as members of LAG 1 Show run int lag 1 - to verify LACP mode active was configured to eliminate LACP blocking states

Answer: C

Question 2

You are configuring a network with a stacked pair of 6300M switches used for distribution and layer 3 services. You create a new VLAN for users that will be used on multiple access stacks of CX6200 switches connected downstream of the distribution stack You will be creating multiple VLANs/subnets similar to this will be utilized in multiple access stacks What is the correct way to configure the routable interface for the subnet to be associated with this VLAN?

Options :

A : Create a physically routed interface in the subnet on the 6300M stack for each downstream switch.

B : Create an SVl in the subnet on each downstream switch

C : Create an SVl in the subnet on the 6300M stack, and assign the management address of each downstream switch stack to a different IP address in the same subnet

D : Create an SVl in the subnet on the 6300M stack.

Answer: D

Question 3

A hospital uses a lot of mobile equipment for the diagnosis and documentation of patient data What Is the ideal access switch for this large hospital with distribution racks of over 400 ports in a single VSF stack?

Options :

A : CX 6300

B : OCX 6400

C : OCX 6200

D : OCX 6100

Answer: A

Question 4

When using the network check page in Central, what kind of tests can you run on switches? (Select two.)

Options :

A : Speed test (iperf)

B : Ping test

C : A full hardware check, including a heavy memory check

D : LED-check.

E : PoE-check

Answer: B,E

Question 5

Describe the purpose of the administrative distance

Options :

A : Routes teamed via external BGP have a higher administrative distance than routes learned via OSPF

B : The administrative distance is used as a trust rating tor route entries

C : The administrative distance for a static route is 10

D : The higher administrative distance is preferred

Answer: B

Free HPE6-A85 Mock Exam – Practice Online Confidently

Buying Options: